S CLASSIX INSIDE news p 18
Modérateurs : Sages, Modérateurs
- gavin sery
- Modérateur
- Messages : 1253
- kuchnie na wymiar Dąbrowa Górnicza Chorzów Jaworzno
- Inscription : mar. 20 nov. 2007, 20:58
- Localisation : Lille
Re: S CLASSIX INSIDE news p 18
Salut ,
j'ai oublié de stipuler c'est vrai , j'ai commandé les fûts chez CVL . Commandés le 2 mai et selon leurs dires "in stock" , ben c'est toujours pas chez moi ..
Concernant la finition , j'arrive pas à me decider tant que j'ai pas reçu les fûts . J'ai besoin de voir le veinage et la teinte naturelle du chateigner ( et le bois mouillé ) pour me decider .
En tout cas ça sera une finition satinée , si teintée elle sera , peut être , comme ça :
J'ai envie d'un truc un peu electrique .. On verra , je mettrais des photos quand j'aurais reçu les fûts .
à tantôt
j'ai oublié de stipuler c'est vrai , j'ai commandé les fûts chez CVL . Commandés le 2 mai et selon leurs dires "in stock" , ben c'est toujours pas chez moi ..
Concernant la finition , j'arrive pas à me decider tant que j'ai pas reçu les fûts . J'ai besoin de voir le veinage et la teinte naturelle du chateigner ( et le bois mouillé ) pour me decider .
En tout cas ça sera une finition satinée , si teintée elle sera , peut être , comme ça :
J'ai envie d'un truc un peu electrique .. On verra , je mettrais des photos quand j'aurais reçu les fûts .
à tantôt
- carlosdubrazil
- Conseil des sages
- Messages : 5942
- Inscription : lun. 26 mars 2007, 11:51
- Localisation : 45°46'03.34"N 4°50'00.44"E
- carlosdubrazil
- Conseil des sages
- Messages : 5942
- Inscription : lun. 26 mars 2007, 11:51
- Localisation : 45°46'03.34"N 4°50'00.44"E
- gavin sery
- Modérateur
- Messages : 1253
- Inscription : mar. 20 nov. 2007, 20:58
- Localisation : Lille
Re: S CLASSIX INSIDE news p 18
J'ai commandé y'a quelques années une série de pigments chez drumfoundry, mélangés à l'eau et appliqués au tampon, ça marche trés bien .
Dans la boutique des fréres Nordin de Lille , il existe aussi toute une gamme de pigments , ça a l'air pas mal , + cher mais de chouettes teintes .
Voilà pour les infos
Dans la boutique des fréres Nordin de Lille , il existe aussi toute une gamme de pigments , ça a l'air pas mal , + cher mais de chouettes teintes .
Voilà pour les infos
- carlosdubrazil
- Conseil des sages
- Messages : 5942
- Inscription : lun. 26 mars 2007, 11:51
- Localisation : 45°46'03.34"N 4°50'00.44"E
- gavin sery
- Modérateur
- Messages : 1253
- Inscription : mar. 20 nov. 2007, 20:58
- Localisation : Lille
Re: S CLASSIX INSIDE news p 18
Peut être, toujours est il qu'en ne ponçant pas, la fibre du bois se reléve et ça fait pas propre du tout, justement je mouille le fût avant teinte et ponçage pour éliminer toute fibre et ce plusieurs fois, aprés rendu ultra lisse je teinte .. mais peut être me trompe je !? empiriquement ça se tient
Tu as prevu de t'essayer à ça ?
Tu as prevu de t'essayer à ça ?
- carlosdubrazil
- Conseil des sages
- Messages : 5942
- Inscription : lun. 26 mars 2007, 11:51
- Localisation : 45°46'03.34"N 4°50'00.44"E
Pas dans l'immédiat.gavin sery a écrit :Tu as prevu de t'essayer à ça ?
Explications du site DF:
The Grain Raising Problem and Preparing the Shell for Staining.
Wet the drum shell surface and allow to dry.
Sand lightly with NO FINER THAN 220 GRIT SANDPAPER.
One big mistake that people make is to sand their drum shells too smoothly before finishing.
Yes, too smoothly!
If you sand the shell until it feels like a baby's butt, the pores of the wood are sealed up and stain cannot penetrate the surface.
This will result in a very lackluster color.
The drum shell should not feel super smooth.
When sanding, make sure you sand with the grain.
If you use a random orbital sander, be aware that you can sand through the outer ply in a flash.
Pay close attention to the seam area, because sometimes there is residual glue in that area that will not allow the stain to penetrate.
If you want to check for problem areas with glue, you can wet a rag with lacquer thinner and wipe lightly on the shell.
There will be a noticable difference in the sheen of the wood if glue is remaining.
The grain raising problem is solved by using a sanding sealer.
The first two coats of topcoat should be treated as the sealer.
Once you spray that on, we suggest using a flexible foam sanding pad (220 grit or higher).
The goal of sanding the sealer is to
1) smooth the surface of "nibs" to prepare for the topcoat, and
2) NOT sand through the sealer and stain!
The goal is not to smooth out orange peel - this will happen later.
- gavin sery
- Modérateur
- Messages : 1253
- Inscription : mar. 20 nov. 2007, 20:58
- Localisation : Lille